{It is always best to open speedometer and count teeth on original gears before ordering to verify correct replacement gear. If you see an optional gear listed below for your vehicle, again the only way to verify the correct gear is to count the teeth on your original gear that is installed in you unit.}

Mechanical Speedometer (cable driven), All Manufactures

With cable driven speedometers, there are potentially two gears that can go bad. First is the odometer gear pictured below. Located on the side of the speedometer. If you have a metal gear then you will not need this gear. If it is plastic inspect very closely where the shaft comes through the gear as there will generally have a hairline crack and this will cause the gear to not fit snugly.

  You will need to count the number of teeth on the original gear before ordering. 10,11, 11 tooth Super beetle, 12,13,14,15,16,17,18,19,21,24 (Chevrolet/GMC),25, 29

Second is the lead gear on the same rail. Check to make sure it is tight on the shaft. Using a small screwdriver, see if it spins on the shaft. If it does, you should replace it also. There are three sizes. All you need to do is measure the overall thickness. 1/8” =4.57mm (thin), 3/16” =5.44mm (medium)or ¼’ = 6.35mm (thick)

Audi On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

80	1986-1992		E15	? small pod
90	1988-1995		E15	? small pod
100 C4 platform	1992-1997		E15	? small pod
5000	Late 1986		E26	15 tooth Large Pod
A6 C4 platform	1992-1997		E15	? small pod
Late Model vehicles with electronic gauges that sweep when the ignition key is first turned.		Requires one gear per gauge. Speedometer, Tachometer, Temperature and Fuel Gauges		E7 Gear

 

Bentley On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

US Spec in MPH	20x23
Euro Spec in KM	20x29

 

BMW On VDO & MotoMeter units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

E23	1977-1986 7 Series	E1=12 tooth	E2=48x12 No Neck	E3=48x17  or 48x19 Neck
E23	1977-1986 7 Series (Euro-KM)	20x23
E24	1976-1989 6 Series	E1=12 tooth	E2=48x12 No Neck	E3=48x17 or 48x19 Neck
E28	1982-1988 5 Series (US Spec)	E1=12 tooth	E2=48x12 No Neck	E3=48x17 Neck
E28	1982-1988 5 Series (Euro-KM)	E1=12 tooth	E2=48x12 No Neck	E3=48x13 Neck
E30	1982-1993 3 Series VDO	E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x14 Neck
E30	1982-1994 3 Series VDO South America	E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x16 Neck
E30	1982-1993 3 Series MotoMeter (US Spec)	E1=12 tooth	MM2=44x16	MM3=40x22		MM4=35x22
E30	1982-1993 3 Series MotoMeter (Asian/Euro) R and K Series Motor Cycle	E1=12 tooth	MM2=44x16	MM3b=40x28		MM4b=28x22
E30	1982-1993 3 Series MotoMeter (Asian/Euro) R and K Series Motor Cycle	E1=12 tooth	MM2c=44x17	MM3c=38x23 .761mm diam.		MM4c=33x23
E30	1982-1993 3 Series MotoMeter (Portugal/Greece) R and K Series Motor Cycle	E1=12 tooth	MM2c=44x17	MM3d=38x28 .822mm diam.		MM4c=33x23
E30	1982-1993 3 Series MotoMeter (Asian/Euro) R and K Series Motor Cycle	E1=12 tooth	MM2d=43x16	MM3e=39x28 OEM color is Red		MM4e=28x22 Inside gear is star shaped. OEM color is tan
E30	1982-1993 3 Series MotoMeter (Asian/Euro) R and K Series Motor Cycle		MM2e=43x17
E30	MotoMeter (Australia) R and K Series Motor Cycle			MM3F=40x34
E31	1989-1999 8 Series	Either Seat Recline Gear	E31 seat gear
E36	1990-2000 3 Series	Driver’s Seat Recline Gear= White	Driver’s Seat Bottom Gear= Pink
E36	1992-1993.5 ; 1997.5-2000	Passenger Seat Recline Gear= Green	Passenger Seat Bottom Gear= Pink
E36	1993.5-1997.5 3 Series	Passenger Seat Recline Gear= White	Passenger Seat Bottom Gear= Pink
E36	1996-2002 Z3	Seat Bushing Kit for Both Seats			Z3 Seat Bushing kit
E39	September 2000-2003 5 Series	Headlight Adjuster kit (one per side)			Fits both xenon and standard
2002	1968-1977	Mechanical 10 tooth for 2002 BMW			Thin lead Gear

 

Chevrolet On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

1997-1999	M24
1997-current Corvette C5 & C6	Seat Bushing Kit
1998-current Pick-up	Seat Bushing Kit

 

Chrysler/Dodge On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

All with Electronic Speedometer except Monaco	E20	16 tooth Medium Pod
Monaco	E25	15 tooth Large Pod

 

Eagle On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

Premier

E25

15 tooth Large Pod

 

Ford On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

Bronco (analog odometer)				Worm Gear
Contour (analog odometer)				Worm Gear
Crown Victoria (only if odometer and trip are stacked in middle of speedometer)		1992-1997	E20	16 tooth Medium Pod
Crown Victoria (only if odometer and trip are split left and right in the cluster)		1992-1997	Drive Gear (2 each)	Worm Gear (2 each)
Expedition (analog odometer)				Worm Gear
Explorer (analog odometer)		1995-2001		Worm Gear
E-series Van (analog odometer)		1995-1998		Worm Gear
F-series Pickup (analog odometer)		1995-1998		Worm Gear
Fairlane Australia	1979-1988			20x29
Fairmont Australia	1979-1988			20X29
Falcon Australia	1979-1988			20x29
Mustang	1994-1999	Drive Gear		Worm Gear (only need to replace if original is black)
Ranger (analog odometer)		1995-2003		Worm Gear
Taurus (analog odometer)				Worm Gear
Thunder Bird		E20		16 tooth Medium Pod

 

Holden On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

Astra LD Australia	1987-1989	E25	15 tooth Large Pod
Commodore VN, VP, VR, VS Australia	1988-1997	E25	15 tooth Large Pod

 

Infiniti

All	2003-2009	Driver's Seat, power and automatic feature (has neck and collar)
All	2003-2009	Driver's Seat, power and without automatic feature (No neck and splined inside)
All	2002-2009	Passenger's Power Seat Gear (No neck and smooth inside)

 

John Deere On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

With electronic Tachometer with odometer

E1=12 tooth

E2=48x12 No Neck

E3=48x15 Neck

 

LaForza On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

1989-

20x29

 

Lincoln On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

If odometer and trip are stacked in middle of speedometer)		1992-1997	E20	16 tooth Medium Pod
If odometer and trip are split left and right in the cluster)		1992-1997	Drive Gear (2 each)	Worm Gear (2 each)

 

Mazda

B series Pick-up

Worm Gear

 

Mercedes-Benz On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

107 = SL Class	1972-1980		M18 or M25	Medium Lead Gear or Thick Lead Gear
107 = SL Class	1981-1989		E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x16 Neck
107 = SL Class Asian and Canadian Spec	1981-1989		E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x13 Neck
107 = SL Class  Euro Spec	1981-1989		E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x18 Neck
123 Chassis	1976-1985		M18	Medium Lead Gear or Thick Lead Gear
124 = E Class (Mechanical)	1984-1995		M18 or M25	Medium Lead Gear or Thick Lead Gear
124 = E Class (Electronic) 400E, 500E, E420, E500	1992-1995		E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x17 Neck
124 = E Class	1984-1995		Bosch Wiper Transmission Gear (U Shaped)/SWF gear not available
126 = S Class Gas	1981-1991		E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x16 Neck
126 = S Class Diesel	1981-1991		E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x15 Neck
126 = S Class Euro Spec	1981-1991		E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x18 Neck
126 = S Class Asian and Canadian Spec	1981-1991		E1=12 tooth	E2=48x12 No Neck	E3=48x12 or 48x13 Neck
129 = SL Class	1990-1998 with analog odometer		E15	12 tooth Small Pod or 16 tooth Small Pod
129 = SL Class	1990-2002		Bosch Wiper Transmission Gear (U Shaped) /SWF gear not available
140 = S Class	1992-1999		E15	12 tooth Small Pod or 16 tooth Small Pod
140 = S Class	1992-1999		Wiper Transmission Gear
201 = 190 Class	1982-1993		Bosch Wiper Transmission Gear (U Shaped) /SWF gear not available
202 = C Class	1993-2000		Wiper Transmission Gear (must grind shaft to install)/Gear inside of motor is NOT available.
Late Model vehicles with electronic gauges that sweep when the ignition key is first turned.		Requires one gear per gauge. Speedometer, Tachometer, Temperature and Fuel Gauges				E7 Gear

 

Mercury On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

Cougar	E20	16 tooth Medium Pod
Grand Marquis (only if odometer and trip are stacked in middle of speedometer)	E20	16 tooth Medium Pod
Grand Marquis (only if odometer and trip are split left and right in the cluster)	Drive  Gear (2 each)	Worm Gear (2 each)
Mystique (analog odometer)	Worm Gear

 

Merkur On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

Scorpio

1988-1989

E20

16 tooth Medium Pod

 

Nissan On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

>

Pintara/Sentra Australia	1986-1993	E25	15 tooth Large Pod
Pulsar N13 Australia	1987-1990	E25	15 tooth Large Pod

Below seat gears are for the following vehicles: Altima, Armada, Frontier, Murano, Pathfinder, Quest, Titan and 350Z

All	2003-2009	Driver's Seat, power and automatic feature (has neck and collar)
All	2003-2009	Driver's Seat, power and without automatic feature (No neck and splined inside)
All	2002-2009	Passenger's Power Seat Gear (No neck and smooth inside)

 

Porsche On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

911 (Mechanical)	1965-1975	M17 (Best to confirm tooth count)
911 US-MPH (Base, Carrera, SC, Turbo)	1976-1989	20x30
911 Euro-KM and Asian (Base, Carrera, SC, Turbo)	1975-1989	20x22 or 20x32 (Best to confirm tooth count)
911 Middle East-KM (Base, Carrera, SC, Turbo)	1975-1989	20x29
911 US-MPH (C2, C2 Turbo, C4)	1989-1998	E15	16 tooth Small Pod
911/930 US-MPH	1986.5-1988	E25	15 tooth Large Pod
911/964 US-MPH option 1	1989-1993	E15	16 or 17 tooth Small Pod
911/964 US-MPH option 2	1989-1993	E25	15 tooth Large Pod
911/964 Australia	1989-1993	E20	15 tooth Medium Pod
911/964 Singapore	1989-1993	E15	17 tooth Small Pod
911/993 US-MPH (C2, C4, T Turbo)	1994-1998	E15	16 tooth Small Pod
911/993 Middle Eastern (C2, C4, T Turbo)	1994-1998	E20	15 tooth Medium Pod
911/993 Euro-KM (C2, C4, T Turbo)	1994-1998	E15	17 tooth Small Pod
912 (Mechanical)	1965-1976	M17
914 (Mechanical)	1970-1976	M17
924S US-MPH (Mechanical)	1976-1988	M17
924S Euro-KM (Mechanical)	1976-1988	M11
928 US-MPH (Base, GT, GTS, S4)	1978-1995	20x21
928 Euro-KM (Base, GT, GTS, S4)	1978-1991	20x21 or 20x29 (Best to confirm tooth count)
944 US-MPH (Mechanical)	1982	M15
944 US-MPH (Mechanical)	1983	M11
944 US-MPH (Mechanical)	1984-1985.1	M17
944 Euro-KM (Base, S, S2, Turbo)	1982-1985.1	20x23 or 20x30 (Best to confirm tooth count)
944 US-MPH (Base, S, S2, Turbo)	1985.2-1991	20x21 or 20x22 (Best to confirm tooth count)
944 US-MPH (Base, S, S2, Turbo)	1991	E25	15 tooth Large Pod
944 Euro-KM	1985.2-1991	20x22 or 20x30
968	1992-1995	E15	12 or 16 tooth Small Pod

 

Rolls Royce On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

US Spec in MPH	20x23
Euro Spec in KM	20x29

 

Saturn On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

1991-1994	E25	15 tooth Large Pod
1991-1994	Shift Grommet, Manual shifting Saturn (located at base of shifter under center console)

 

Vixen Motor Home On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

1986-1989

20x23 or 20x29

 

Volkswagen On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

Mechanical (cable driven)	Lead Gear (need to measure original gear, see top off page)
Beetle and Super Beetle	1972-	VW11, VW12
Bus (Type 2)	1968-1979	VW11 or M11
Rabbit	1980-1982	M21
Late Model vehicles with electronic gauges that sweep when the ignition key is first turned.	Requires one gear per gauge. Speedometer, Tachometer, Temperature and Fuel Gauges	E7 Gear

 

Volvo On VDO units you need to open and count the teeth on the old gears to ensure that you order the correct tooth count. Part numbers from any part of the speedometer do not help in determining the tooth count.

200 Series	1986-1991	E25	15 tooth Large pod
200 Series	1992-1993	E25 or E26	15 tooth Large pod
440/460 Series (Only with Analog VDO Odometer)	1987-1997	E20	16 tooth Medium pod
700 Series (Only with VDO unit)	1982-1988	E26	15 tooth Large pod
850	1992-1997	E15	12 tooth Small Pod
850	1992-1997	Horn Kit (consist of 4 each: bolt, washer, Plastic grommet, speed nut)
C/S/V 70 Series	1996-2000	Horn Kit (consist of 8 plastic bushings)
VDO unit		UAF 2115 bipolar Integrated circuit chip (Has to be soldered) not common problem unless power and ground for cluster is reversed when reinstalling cluster.

If you have questions, please email or call anytime. Weekends and evenings are ok.
sales@odometergears.com
757-593-3478 (Jeff)
757-771-6694 (Darren)
You can also text message to the above phone numbers